+62-21-344 2919      +62-21-3511 428      +62-811-9119-611   
    deltacrete@gmail.com      Senin - Jumat 9.00 - 17.00

Deltacoat ESF

High Gloss Solvent Free Epoxy Coating


Deltacoat ESF is a two-component solvent free epoxy coating that suitable for coating of wallsystem. The cured film of Deltacoat ESF forms a hard, gloss and smooth layer with excellent adhesion to concrete substrate.


Deltacoat ESF is recommended to areas where chemical resistance and aspects are required. Deltacoat ESF is recommended for use in floor of warehouses, industrial and food processing areas, kitchen, laboratory, engineering workshops, and car parks.


Impervious seamless and jointless surface, easy to clean and maintain, hygienic, chemical resistance, excellent wear and abrasion resistance and have aesthetic state of art.


Deltacoat ESF consumption is 0.25 – 0.3 kg/m2 for 175 micron thickness. Please kindly contact DELTACRETE to have appropriate technical assistance for the recommended thickness since material performance may vary at different surface.


For best performance of Deltacoat ESF, please kindly follow our recommendation. Preparation is a must before application. For new concrete, allow the concrete to cure at least 72 days. Humidity is not more than 75% measured in accordance with BS 8203. Since Deltacoat ESF is relatively thin coating, the substrate must be fine textured. Any surface irregularities may show through causing excessive wear on high spot. Concrete substrate must be structurally sound, clean, dry and free from all traces of loose material, laitance, oil and grease. Any unsound material must be removed before application. Preparation by captive blasting or diamond grinding is ideal for surface preparation. Priming using Deltaprime series will enhance the adhesion of top coat with the concrete. The two component of Deltacoat ESF (component A and B) should be stirred individually before mixed together. Put both component in a mixing vessel and mix them thoroughly using low speed drill and mixing paddle mixer. Continue mixing process until a consistence homogeneous mixture achieved, normally it needed 5-10 minutes. Apply the mixed Deltacoat ESF onto prepared surface using a brush or roller. Ensure that the area is completely coated and that ‘ponding’ material does not occur.


Tools and equipment should be cleaned immediately after use, while the mixture are still un-cured with solvent cleaner. When mixture already harden, please kindly remove the material mechanically.


Pot Life 100 minutes
STT 4 hours
Initially hardness 9 hours
Fully cured after 3 days
(ambient temperature may have some effect on the curing time)


Form Liquid (component A and B)
Viscoty Enamel 8580 cps
Viscoty Hardener 400 cps
Specific Gravity Mix 1.30 – 1.40
Shelf Life 1 year when unopened and stored in dry conditions
Packaging 4 kg set (Component A+B)
Comp. A (enamel) : 3 kg/can
Comp. B (hardener) : 1 kg/can


Deltacoat ESF should not be applied on the surface known to, or likely to suffer from, rising dampness, potential osmosis problems or have a relative humidity greater than 75%. If movement or cracking of the substrate takes place after application then reflective cracking of topping may occur. Ambient temperature when application is more than 100C.


Deltacoat ESF range of products can cause skin irritations in persons with sensitive skin. Wear protective clothing like gloves, goggles and respiratory equipment, particularly in confined spaces. Ensure adequate ventilation and avoid inhalation of vapors. If splashed into the eyes, nose, mouth or throat, flush immediately with plenty of clean, warm water and seek medical attention without delay.


Deltacoat ESF in non-flammable material.

Our Location

PT. Deltacretindo Wira Mandiri
  JL. Pintu Air IV No. 41A
  Jakarta, Indonesia 10710
  +62-21-344 2919
  +62-21-3511 428
   :  deltacrete@gmail.com

haki cm

© 2017 Deltacretindo. All Rights Reserved. Powered By GM-Portalindo