+62-21-344 2919      +62-21-3511 428      +62-811-9119-611   
    deltacrete@gmail.com      Senin - Jumat 9.00 - 17.00

Deltacoat HCR

High Chemical Resistant Surface Protection Epoxy

DESCRIPTION

Deltacoat HCR is a high performance two components solvent based epoxy coating which is used in all kinds of manufacturing, storage and processing areas to provide an excellent chemical resistant.

Deltacoat HCR can be applied on concrete / cement based surface, mild steel, zine.

USES

High chemical resistant surface protection for wall and light duty area.

ADVANTAGES

  • Excellent Chemical Resistance
  • Formulated for use in hot climates
  • Good adhesion to the concrete substrate

APPLICATION INSTRUCTION

Surface Preparation

For maximum product performance, proper and thorough surface preparation is necessary. This is particularly important in aggressive industrial or high corrosion environments. The surface to be coated must be clean and free of rust, dirt, oil, grease, wax, mildew, defective old coating and other poorly adhering material that could interfere with adhesion. Avoid the inhalation of dust.

New surfaces must be brushed with a stiff brush to remove all loose surface materials porous surfaces must be sealed with a thinned first coat.

Mixing

Stir component 'A' thoroughly, then mix with component 'B' in a 4 : 1 weight ratio. Stir this mixture thoroughly for 3 minutes and allow a 5-minutes induction time before application. This ratio of mixing should not be varied, and should be finished use in 1 hour.

Application

For brush application, use a quality synthetic filament brush. For rolling, use a short nap mohair cover. Deltacoat HCR dries to touch in 3 hours, dry in 6 hours. Any preexisting finish that is glossy will need to be sanded before top coating. Cured in 1 day, full durability of the coating is achieved after the normal 7 days curing period.

Cleaning

After use, remove as much paint as possible from brushes before cleaning with solvant (Tolusne/Xylene).

Do not use or store in extremes of temperature and protect from frost.

TECHNICAL DATA

Properties Remark
Color See color card
Binder Amine Cured Epoxy Resins
Mix Ratio A : B = 4 : 1 (weight ratio)
Badly actived or incorrestly mixed
materials will affect performance and may
cause early failure or discoloration. Stir A
component when adding B component to
help achieve thorough mixing of the two
components, allow 5 minutes induction
time.
Solid 60 %

Coverage

1 kg / 4 m2
Film Thickness 100 um ( wet thickness)
STT 1 hours @ 30 ºC
Pot Life 1 hours @ 30 ºC
Cure Time 1 days .
Full durability of the coating is achieved
after the normal 7 days curing period.
Chemical Resistance Excellent
Chemicals
Film Performance
NaOH (pH = 14) Ok, no discolaration
H2SO4 (pH = 1) Ok, only discoloration
HC1 (pH = 3) Ok, only discolaration
*) after immersion in 28 days
Solvent Toluene

Note : The resotion of epoxies commences immediately after the two components are mixed. This reastion is temperature related and so the curing time will be approximately halved by a 10ºC for sealing new or have surfaces apply epoxy primer before top coat.

HEALTH AND SAFETY

Deltacoat HCR contains epoxy resins which can be irritating to eyes and skin. Wear suitable protective clothing – eye protection, gloves and respiratory equipment, particularly in confined spaces. Avoid contact with skin and eyes. In case of contact with the skin, rinse with plenty of clean water, then cleanse thoroughly with soap and water. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately. Avoid the inhalation of dust, wear a suitable face mask if dry sanding.

Keep out of the reach of children.

FIRE

Deltacoat HCR is flammable materials.

Our Location

PT. Deltacretindo Wira Mandiri
  JL. Pintu Air IV No. 41A
  Jakarta, Indonesia 10710
  +62-21-344 2919
  +62-21-3511 428
  +62-811-9119-611
   :  deltacrete@gmail.com

haki cm

Print
© 2017 Deltacretindo. All Rights Reserved. Powered By GM-Portalindo